# $Id: att-dataport,v 1.1.1.1 2005/11/11 21:32:01 faxguy Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for using the Class 1 command interface with
# an AT&T DataPort 14.4 modem.  Firmware version 122 (ati1)
# or newer.
#
# Hardware flow control is used by default.
#
# Note that due to a bug in the 1.22 firmware the FCS bytes in the HDLC
# frames are NOT returned to the host.  This is fixed in versions 1.33
# and later.  To deal with this problem, early firmware revs should be
# sure to have Class1FrameOverhead set to 2 instead of the normal 4.
#
# CONFIG:CLASS1:144:.*:.*: Manufacturer='AT&T' Model=Dataport
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use class 1 interface
ModemRate:		19200
ModemFlowControl:	rtscts		# default
#
ModemHardFlowCmd:	AT&R0\D1\Q3	# use RTS/CTS and enable RS232 handling
ModemSoftFlowCmd:	AT&R1\D0\Q1	# use RTS/CTS and enable RS232 handling
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier
ModemSetupAACmd:	AT+FAA=0	# disable in case of Class 2 support
#
ModemMfrQueryCmd:	!AT&T
ModemModelQueryCmd:	!DataPort
ModemRevQueryCmd:	ATI19
#
# NB: this works around a bug in the 1.22 firmware; it is fixed
# in versions 1.33 and later in which case you can remove this
# line and use the default value of 4 (though leaving it as 2
# won't harm anything).
#
Class1FrameOverhead:	2		# 1.22 firmware does not include FCS
#
# The modem returns "OK" when there is a timeout before carrier is
# established.  This is treated as "NO CARRIER" by faxd.  Thus we
# need to up the NoCarrierRetrys parameter to avoid having the server
# reject jobs prematurely.
#
NoCarrierRetrys:	3		# retry 3 times on no carrier
#
PagerSetupCmds:		ATS41=10%B300	# use V.21 at 300 bps