# $Id: dsi-scout+,v 1.1.1.1 2005/11/11 21:32:01 faxguy Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for using the Class 1 command interface with
# a Digicom Systems, Inc (DSI) Scout+ modem.  Firmware version
# 2A19/2931 (ati1?) or newer.
#
# XON/XOFF flow control must be used in firmware revisions before
# 3507/3506 because the modem does not honor RTS/CTS during page
# transfers.  Later revisions permit the configuration of RTS/CTS
# flow control through a new (undocumented) register, S24:
#
# Value	Meaning
#   0	use XON/XOFF in fax mode
#   1	use RTS/CTS in fax mode
#   2	use what is specified by *F in fax mode
#
# Note also that the value of S24 is not permanent.  It is reset
# after each disconnect.  On power on S24 is 0.  S24 is unchanged
# by the &F command.
#
# CONFIG:CLASS1:961:.*:.*: Manufacturer=Digicom Model=Scout+
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# hint to override class 2
ModemRate:		19200
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT*F0		# disable flow control
ModemSoftFlowCmd:	AT*F2		# software flow control
ModemHardFlowCmd:	AT*F3		# harware flow control
ModemSetupDTRCmd:	AT&D3		# DTR off causes modem to reset
ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
#
Class1SFLOCmd:		ATS24=0		# use XON/XOFF in fax mode
Class1HFLOCmd:		ATS24=1		# use RTS/CTS in fax mode
#
ModemMfrQueryCmd:	!Digicom
ModemModelQueryCmd:	!Scout+
ModemRevQueryCmd:	ATI1
#
ModemDialCmd:		ATDT%s		# T for tone dialing
#
# NB: if your modem supports S24 as described above then
#     these can be removed.
#
ModemAnswerFaxBeginCmd:	"<xon>"		# use XON/XOFF for fax recv
Class1Cmd:	"AT+FCLASS=1\n<xon>"	# use XON/XOFF for fax send