# $Id: rc144ac,v 1.1.1.1 2005/11/11 21:32:01 faxguy Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a Rockwell V.32AC Class 2 modem
# (RC144AC, RC96AC or using RC144DP).
#    Boca M1440E		firmware V1.270 or newer
#    Dallas Fax			(throw it away!)
#    Hayes Optima 24+Fax96	firmware TR00-J260-001 XXX or newer
#    SupraFAX v.32bis		firmware V1.200-C or newer
#    Twincom 144/DF		firmware rev V1.200 or newer
#    Dynalink 1414VE		firmware rev ???
# (and others)
#
# This configuration file sets up the modem to run at 38.4 with
# RTS/CTS flow control used by default.  XON/XOFF is automatically
# enabled for fax recv.  Beware of modems that also lock sending
# to 19.2; add ModemSendBeginCmd: "<19200>" if this is required.
# Also beware that the adaptive-answer facility, when supported,
# is often unreliable.
#
# CONFIG: CLASS2: *-V.32AC-*
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		19200
ModemFlowControl:	rtscts		# default
#
#ModemResetCmds:	AT&F2		# what you want for a Supra
ModemNoFlowCmd:		AT&K		# disable flow control cmd
ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
ModemSoftFlowCmd:	AT&K4		# software flow control cmd
ModemSetupDTRCmd:	AT&D3		# DTR off causes modem to reset
#ModemSetupDTRCmd:	AT&D2S25=1S38=0	# Dynalink 1414VE needs this
ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
ModemSetupAACmd:	AT+FAA=1+FCLASS=0 # enable in current class
#
ModemSendFillOrder:	LSB2MSB		# as expected
ModemRecvFillOrder:	MSB2LSB		# opposite of what makes sense
#
ModemAnswerFaxBeginCmd:	"<19200><xon>"	# modem switches on fax receive
#
# Caller ID configuration setup for Supra.
#
#QualifyCID:		etc/cid		# CID access control list file
#CallIDPattern:		"NMBR = "	# pattern string for phone number info
#CallIDPattern:		"NAME = "	# pattern string for identity info