# $Id: usr-rts,v 1.1.1.1 2005/11/11 21:32:01 faxguy Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and RTS/CTS flow control. 
#
# CONFIG:CLASS1:1444:.*:RTSCTS: Manufacturer=USRobotics Model=Courier/Sportster
# CONFIG:CLASS1:1445:.*:RTSCTS: Manufacturer=USRobotics Model=Courier/Sportster
# CONFIG:CLASS1:2886:.*:RTSCTS: Manufacturer=USRobotics Model=Courier/Sportster
# CONFIG:CLASS1:3366:.*:RTSCTS: Manufacturer=USRobotics Model=Courier
# CONFIG:CLASS1:3361:.*:RTSCTS: Manufacturer="USRobotics w/TI Chipset" Model="Sportster 33600"
# CONFIG:CLASS1:3362:.*:RTSCTS: Manufacturer="USRobotics w/TI Chipset" Model="Sportster 33600"
# CONFIG:CLASS1:3367:.*:RTSCTS: Manufacturer="USRobotics" Model="Courier"
# CONFIG:CLASS1:5601:.*:RTSCTS: Manufacturer="3Com U. S. Robotics" Model="3CP5610"
# CONFIG:CLASS1:5607:.*:RTSCTS: Manufacturer="3Com USRobotics" Model="Courier V.Everything"
# CONFIG:CLASS1:5608A:.*:RTSCTS: Manufacturer="3Com USRobotics" Model="Courier"
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use class 1 interface
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	rtscts		# hardware flow control
#
ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
ModemResultCodesCmd:	ATQ0X4		# enable result codes
#
ModemMfrQueryCmd:	!USR
ModemModelQueryCmd:	ATI3
ModemRevQueryCmd:	ATI7		# XXX, returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:		AT&H0&I0&R1	# setup modem for no flow control
Class1HFLOCmd:		AT&H1&I0&R2	# setup modem for hardware flow control
Class1SFLOCmd:		""		# modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:	AT+FCLASS=0&H1&I0&R2	# leave modem in class 0
ModemAnswerCmd:		AT+FCLASS=1&H1&I0&R2A	# force RTS/CTS after change
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0